Plumbing 101: What You Must Have for Installing a Bathtub
Plumbing 101: What You Must Have for Installing a Bathtub
Blog Article
This post listed below relating to Tools You Need to Install a New Bathtub is exceptionally attention-grabbing. Check it out for yourself and see what you think of it.
Installing a bathtub isn't precisely brain surgery, yet it does call for strong plumbing, carpentry, and sometimes, tiling skills. Changing an old bathtub with a brand-new one is likewise a reasonably challenging job. If the old bathtub is conveniently available, the project can relocate speedily; if you have to open a wall surface to eliminate the old tub as well as position the new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly require an assistant to move out the old bathtub and also embeded in the brand-new one. See to it you have actually qualified yourself for the work as well as are comfortable attempting it. Instead of hiring a service provider to take control of a halfway-completed task, it is better to consider using one prior to you begin. Opportunities are you might need a professional plumber to make tube connections.
This write-up will certainly assist you set up a brand-new bath tub in your bathroom if you have currently purchased a brand-new tub and don't need to alter the plan of your previous water system pipelines.
Your devices as well as material list ought to consist of the following:
Preparing for the Setup
Firstly, the sustaining frame provided with the bath must be fitted (if called for) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is very important to see to it that if the tap includes a plastic washing machine, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final setting.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you ought to do is detach the water system. After doing so, switch on the taps to drain any type of water staying in the system. The procedure of removing the existing faucets can be quite problematic due to the limited gain access to that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel prepared for the remaining water that will certainly come from the pipes. Once the supply pipelines have been eliminated, utilize the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from turning during this procedure. Once the faucets have actually been gotten rid of, the holes in the bath/basin will have to be cleaned up of any type of old securing compound.
Before carrying on to fit the brand-new taps, contrast the pipeline links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is required for the brand-new faucets to fit.
Installing the Bath tub
Using both wooden boards under its feet, place the bathtub in the called for placement. The wood boards are useful in equally spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto four small factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by checking the spirit level and changing the feet on the bath tub until the level reads degree.
To install faucets, fit the bottom of the outermost flexible faucet port to the suitable supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water system and also inspect all joints and new pipework for leakages and tighten them if needed. Fill the tub and likewise inspect the overflow electrical outlet as well as the normal electrical outlet for leakages.
Lastly, repair the bathroom paneling as described in the maker's user's manual. Tiling and sealing around the bath tub should wait up until the bathtub has actually been made use of at least when as this will certainly settle it into its final placement.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipelines.
If you require to fit a monobloc, after that you will need reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the installing hole in the bath/basin making sure that the washers remain in place between the tap and the sink. Secure the faucet in position with the manufacturer offered backnut. Once the tap is securely in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The previous kind should be connected to the faucet ends first, tightening just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bath tub
In the location where the bath meets the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture an inflexible seal, triggering the water to penetrate the wall between the bath and also the tiling, causing difficulties with wetness and also possible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes and cartridges, and are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked newspaper or soft rope. Keep in mind to always fill the tub with water before securing, to allow for the motion experienced when the bathtub remains in use. The sealant can fracture fairly very early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also quickly offered on the market. It is recommended to fit the floor tiles making use of waterproof or waterproof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I ran across that blog posting about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing a search on the web. Kindly take a moment to share this content if you appreciated it. I recognize the value of reading our article about How to Install a Bathtub.
Request our emergency plumbing support. Report this page